Sevgili vış sürekli sallaman beni çok üzüyor:
D2F Switches:
<br style="color:#cccccc;" />
The switches by Omron are all designated D2F, from there it gets a bit more complex. We'll discuss retail switches first, as once you understand them, you can more easily understand the machine switches.
<br style="color:#cccccc;" /><br style="color:#cccccc;" /><br style="color:#cccccc;" />
D2F vs D2FC
indicates origin and more.
<strong style="color:#cccccc;">(Important!)</strong>
LESS
D2F = Japanese (always has Japan molded into top along with Omron label)
D2FC = China (may have China painted on side or top, or just a “C” in the model #)
Chinese models are mass produced and are considered to be a bit sloppy in tolerances, so one may have an actuation point a bit higher than another. Tolerances on these are pretty small so you wouldn't notice, but just know that they are more sloppy than the Japanese models.
Japanese models have much nicer internals, better tolerances, better metals,a stronger frame and are better sealed from dirt and moisture. They are also slightly taller and have a shorter actuation distance, it's for this reason they are not always interchangeable with Chinese models.
Which is better?
No question, the Japanese switch is better made, but unless you use it in a harsh environment, or plan on your mouse lasting 10 years or more it may not be worth the added expense or hassle to install them.
Warning: If your mouse has Chinese models, the Japanese models may not fit (unless there is a teeny bit of slop between button and switch itself, which is common). Most Logitech can probably handle it, but if not you can always file actuator. Just remember if you don't like it and try to go back to the Japanese version things will be very sloppy.
<br style="color:#cccccc;" /><br style="color:#cccccc;" />
D2F vs D2F -01
(can be with or without the dash)
<br style="color:#cccccc;" />
The next batch of numbers or lack of them is usually an 01, this indicates the spring material.
LESS
D2FC Indicates a “silver alloy spring”
D2FC -01 Indicates a “gold alloy spring”
I put them in quotes because I suspect it means they are plated spring steel, not an actual alloy of the two materials as implied by Omron.
Which is better?
Gold is better at fighting corrosion, however it doesn't conduct as well and needs a bit more power to start conduction. In our situation, it doesn't matter much and given time and corrosion (tarnish), the gold will maintain it's level of resistance better. So unless you need the added conductivity for higher amps, gold is the better choice here as evidenced by the act that better mice almost universally use the 01.
<br style="color:#cccccc;" /><br style="color:#cccccc;" />
Spring rates (-F)
LESS
The next important indicator you want to know is the -F
D2FC =150g actuating force
D2FC -F = 75g actuation force
Which is better?
Now before you rush out and look for a -F, there are considerations here and it's really not that simple.
-F will obviously be easier to push and likely will last longer (irrelevant, you'll see). A non -F will have a much more solid click to it and a faster return. This is important if you play FPS and need to rapid fire. Most people tend to prefer the non -f, especially in gaming mice, but if you don't game the -f may be your favorite and I can see some of you already drooling, but...
Warning: I told you this wasn't that simple…
Switches have a max force rating which happens to be based on the switch and is typically 10x the actuation force. So if you tend to abuse your mice, the non -f can actually last much longer. Just another reason for gamers to consider the non -F. As you start pounding the button for rapid fire, you can easily exceed the -F's force limits which is only a little over a pound. This becomes more relevant in the next section.
<br style="color:#cccccc;" /><br style="color:#cccccc;" />
Lifespan
Will be labeled as D2F -01 (10M)
LESS
Remember I said lifespan on the -F was irrelevant, now you learn why.
There is a rumor that Japanese switches start with a lower lifespan and that the -F has a longer lifespan. This doesn't seem to really hold much water when you consider that Omron themselves labels them for you. Sometimes.
Warning: Keep in mind that these numbers are without any load, and they really do mean ANY load. If the mouse button rests on the switch button or your finger causes it to, then the lifespan will be shortened. Anything touching that button shortens the lifespan. Your mouse may have some slop to prevent this when your fingers are off the mouse, but as soon as you put them on it, the lifespan is probably starting to drop as the weight of your fingers remove that slop. Personally, 10M last longer than 20M for me, see my note
here.
Omron has multiple ratings:
(1M) = 1million presses
(3m) = 3million presses
(5m) = 5million presses
(10M) = 10million presses
(20M) = 20million presses
Unfortunately, the only surefire way to know for certain is with the part number as shown above as they didn't always mark them. However they often coincided with the button color or a painted dot on top.
Some of the lower numbers the details are sketchy, but we don't really care about them anyhow.
Black – no dot – (1M) = 1million presses (not verified)
Red or Yellow button or dot (3m) = 3million (not verified)
Red or Yellow button or dot (5m) = 5million (not verified)
Gray button and/or dot - (10M) = 10million
White button and/or dot - (20M) = 20million
The colors are also referred to as tops, so when someone says a “white top” Omron, they mean it's a switch rated for 20mil. Presses.
Caution: I don't recommend relying on the button color. MS has custom switches made for them (labeled MS) which can be different and I have seen white and gray botton Omrons with no (XXM) stamped on them. These are usually older models, but it's something to keep in mind. Dots and labeling is the only surefire way to know and a while lower numbers may not say it, you can bet a 20M is going to let you know it's a 20M.
I'll put a chart at the bottom showing what is using what that I know of and if others post I will try and add them.
<br style="color:#cccccc;" /><br style="color:#cccccc;" />
Other random numbers and letters in the switch part number
Example D2F L3 -T
LESS
Frankly, you do not want any of these on your switch, as they pertain to the soldering terminals and different ways to actuate the button, almost none of which are useful to use. Note: Levers can be removed, so if you want a specific switch in a hurry and can only find it with a lever, you can always remove it from the switch and use it without problems, just be careful removing it.
L = Hinge lever
L2 = Roller lever
L3 = simulated roller
L30 = larger simulated roller
-T = self clinching terminals (this can still work in a mouse)
-A = right angled terminals
-A1 = left angled terminals
-D3 = big solder terminals
-D = compact terminals
<br style="color:#cccccc;" />
Machine switch Numbers
<br style="color:#cccccc;" />
Other Switch Brands
vs vs